|
|
|
|
|
|
Lomanco VPLUG Foam End Plug, For Use with VUR Ridge Vents, Polyethylene, Black
|
|
|
Tight-fitting, high-density foam end plug. To be used in conjunction with VUR ridge vents.
|
|
|
|
|
|
|
|
|
|
Joint Strap Black Aluminum - Case of 36
|
|
|
Joint straps for AR10 series aluminum ridge vent. Miami Dade County Approved #NOA 99-0422.04. Nos.ARSBLF, ARSBRF, & ARSWHF Florida Building Code (FBC) Approved FL 5027.
|
|
|
|
|
|
|
|
|
|
Quarrix Building Products 58784 Ridge Vent, 11-1/4 in W x 20 ft Roll L x 5/8 in T, Polyethylene
|
|
|
Use under asphalt shingles, metal roofing, cedar shakes or slate; virtually invisible with low-profile design; no baffle to collect debris or clog; HDPE crush-resistant material; adapts to roof pitches 3/12 to 20/12; certified by ICC, BOCA, ICBO, UL CLASS A or C, TDI and Miami Dade county.
|
|
|
|
|
|
|
|
|
|
Cobra 2005 Shingle Over Coil Ridge Vent, 10-1/2 in W x 20 ft Roll L, High-impact Polymer
|
|
|
Use on roof pitches from 3/12 to 20/12. Helps remove excess heat and moisture to protect against premature roof deterioration and helps prevent problems with birds, insects and animals in attic. Prevents roof rot in attic or roof deck. Minimizes peeling and extends the life of exterior and interior paint. Limits mold growth. Easy to install, shingle over design is virtually invisible when installed. Includes "Smart Nails" for hand-nailing, or 1-3/4" coil nails for nail guns. Meets or exceeds all code requirements. 16.9 sq. ins. per linear foot of net free ventilating area when hand-nailed. 14.1 sq. ins. per linear foot of net free ventilating area when using nail gun. Will not crack or dent during installation. Won't corrode, rust, or turn brittle. Works with traditional size ridge cap shingles.
|
|
|
|
|
|
|
|
|
|
Ridge Vent End Plug Black Foam - Case of 24
|
|
|
Tight-fitting, high-density foam end plug. To be used in conjunction with LPR ridge vents.
|
|
|
|
|
|
|
|
|
|
Ridge Vent End Plug/connector - Case of 36
|
|
|
For all AR10 series ridge vent.
|
|
|
|
|
|
|
|
|
|
Lo-OmniRoll LOR-30 Ridge Vent, 30 ft L
|
|
|
Can be installed with a pneumatic nail gun or hammer. Two coils of 1-3/4" nails provided. External convolute baffles - incurved design allows flexibility to roll up and out while maintaining its shape. Can be cut at one foot intervals - multiple cut lines eliminates unnecessary scrap. Weather protection and performance with no filter to clog. Molded fanfold end plug. Molded centerline. Nail holes marked every 6" - supported every foot. 11 square inches of net free ventilating area per lineal foot. External venturi baffle. Adjusts from 2/12 to 16/12 roof pitches. Limited lifetime warranty- the engineered material guarantees it will last as long as your shingles. Miami Dade County Approved 13-0701.11. 52 CFM at wind velocity of 3 MPH; 148 CFM at wind velocity of 8 MPH; 283 CFM at wind velocity of 15 MPH.
|
|
|
|
|
|
|
|
|
|
Ridge Vent 4ft Cobra Iii - Case of 10
|
|
|
Shingle-over to blend into ridge line. Allows heat/condensation to escape at most effective location. Watertight, passes 110-MPH wind-driven rain test. External baffles help deflect wind/rain, no end caps needed. Prevents roof rot in attic or roof deck. Minimize peeling and extend the life of exterior and interior paint. Limit mold growth. Specially-designed louver spacing helps keep insects out. Energy-efficient, crush-resistant, with internal structural support for added durability. Extra-flexible hinge design for installation on 3:12 to 16:12 sloped roofs. 3" ring shank nails included to insure proper fastening. Edge overhang for smooth, continuous coverage between sections. Provides 18 sq.in/linear foot net-free ventilating area. 40' replaces 18 conventional or ten 12" turbine roof vents. Hip/ridge compatible with traditional sizes (11-1/2 x 12"). "EasyTear" feature allows product to be hand-torn in 3" increments. Boxed.
|
|
|
|
|
|
|
|
|
|
Omni Ridge 4ft Baclk Plastic - Case of 10
|
|
|
Internal aerodynamic curved baffles. 18 square inches of net free ventilating area per lineal foot. External perpendicular omni baffles. Weatherproof under-lapping joint. Four drain holes per foot per side. External venturi baffle. Pre-formed to 3/12 pitch. 10 supported nail holes. Alignment tabs. External water shield. Slot width guide lines. Adjusts from 2/12 to 16/12 roof pitches. Co-polymer materials. Limited lifetime warranty- the engineered material guarantees it will last as long as your shingles. No connectors required. Molded fanfold end plugs - no accessories or alterations needed. Miami Dade County Approved 16-0510.27. 95 CFM at wind velocity of 3 MPH; 235 CFM at wind velocity of 8 MPH; 430 CFM at wind velocity of 15 MPH; OR4 with nails and OR4 with screen available.
|
|
|
|
|
|
|
|
|
|
Ridge Vent 10ft Brown Metal - Case of 10
|
|
|
One-piece construction. Male/female connections - no straps necessary. Engineered weather infiltration protectors at each connection. Pre-punched nail holes. Exterior wind baffles. Adjusts from 3/12 to 8/12 pitches. 18 square inches of net free ventilating area per linear foot. Miami Dade County Approved 16-0510.24. 34 CFM at wind velocity of 3 MPH; 95 CFM at wind velocity of 8 MPH; 181 CFM at wind velocity of 15 MPH.
|
|
|
|
