|
|
|
|
|
Tru-Flate 18-603 Blow Gun, 150 psi Air
|
|
Adjust from low air to a full volume flow. Recommended air pressure to 150 psi maximum. Knurled nozzle makes handling easy. Complete with handy pocket clip. Fits all industrial/Milton design 1/4 in coupler bodies.
|
|
|
|
|
|
|
|
Tru-Flate 18-231 Blow Gun, 150 psi Air
|
|
Conforms to all Federal requirements related to OSHA, including noise level regulations. Tamperproof pressure reducers built into this gun limit nozzle pressure to 30 psi or less when used with listed inlet pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast, epoxy finish body. Complete with hang-up hook and 1/4 in female NPT inlet.
|
|
|
|
|
|
|
|
Tru-Flate 18-143 Blow Gun, 150 psi Air
|
|
Converts any standard ball foot tire chucks to a safety blowgun. Vented nozzle and built-in pressure reduces limit nozzle pressure to a maximum of 30 psi, with up to 150 psi inlet pressure. Conforms to #1001 OSHA regulation. Epoxy finish.
|
|
|
|
|
|
|
|
Tru-Flate 18-319 Blow Gun with Extension, 150 psi Air
|
|
Vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast body. Hang up hook and 1/4 in NPT female inlet included. Meets OSHA regulation 1001 for 30 psi "dead head" pressure. Inlet pressure rating of 150 psi.
|
|
|
|
|
|
|
|
Bostitch BTFP72330 Blow Gun
|
|
Safety blow gun.
|
|
|
|
|
|
|
|
Tru-Flate 18-233 Blow Gun, 150 psi Air
|
|
Increased performance and yet still meets OSHA regulation 100-1 for 30 psi "dead head" pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast body. Complete with hang-up hook and 1/4 in NPT female inlet. Inlet pressure of 150 psi.
|
|
|
|
|
|
|
|
ProSource CC970 Air Blow Gun, 50 psi Air, 5-10 CFM Air
|
|
Ideal for cleaning damaging dirt and grime buildups from large machinery, engines and heavy equipment.
|
|
|
|
|
|
|
|
Tru-Flate 18-302 Blow Gun with Extension, 150 psi Air
|
|
Meets OSHA regulation 100-1 for 30 psi "dead head" pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast body with hang-up hook, 1/4 in NPT female inlet and 4 in extension.
|
|
|
|
|
|
|
|
Tru-Flate 18-207 Blow Gun
|
|
Allows full line pressure to be used. Oil-resistant, soft replaceable rubber tip. Will not mar delicate surfaces. Gives a leakproof seal against oil passages, fuel lines and more. When air pressure is needed for cleaning.
|
|
|
|
|
|
|
|
Tru-Flate 18-241 Blow Gun Kit
|
|
Interchangeable nozzles for cleaning and inflating. Complies with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 psi. Includes standard nozzle, tapered inflator nozzle and ball inflator nozzle.
|
|
|