|
|
|
|
|
|
USP Lumber PAU44-TZ Post Anchor, 4 X 4 in, 2000 psi, 12 ga, 2535 lb Uplift Douglas Fir, Steel
|
|
|
Used to secure wood posts to concrete footings and to provide moisture damage protection. Higher uplift resistance an optional bolt fastening to post. Features a 1" stand-off plate to evaluate wood posts above concrete surfaces. Drain slots allow the anchors to shed water. Triple zinc finish for ACQ pressure treated lumber. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires (12) 16d HDG nails or (2) 1/2" HDG bolts and (1) 5/8" anchor bolt for installation. Meets ICC-ES ESR-1881, FL821, L.A. City RR 25779 and Dade County, FL 07-0306.06, PAU44-TZ and PAU66-TZ codes.
|
|
|
|
|
|
|
|
|
|
USP Lumber PAU66-TZ Post Anchor, 6 X 6 in, 2000 psi, 10 ga, 2380 lb Uplift Douglas Fir, Steel
|
|
|
Used to secure wood posts to concrete footings and to provide moisture damage protection. Higher uplift resistance an optional bolt fastening to post. Features a 1" stand-off plate to evaluate wood posts above concrete surfaces. Drain slots allow the anchors to shed water. Triple zinc finish for ACQ pressure treated lumber. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires (12) 16d HDG nails or (2) 1/2" HDG bolts and (1) 5/8" anchor bolt for installation. Meets ICC-ES ESR-1881, FL821, L.A. City RR 25779 and Dade County, FL 07-0306.06, PAU44-TZ and PAU66-TZ codes.
|
|
|
|
|
|
|
|
|
|
Tz Post Cap 4x4-6in 2-Piece st - Case of 20
|
|
|
For light-duty post-to-beam connections. Quick and easy installation on decks, carports and other projects. Use two caps for each installation project to act as a unit. Designed to work with single, solid sawn beams, but can be used with build-up beams made of 2x lumber and shims fastened. "-TZ" following item number indicates Triple Zinc finish. "-GC" following item number indicates Gold Coat finish. Meets ICC-ES ESR-1781, FL18285 and L.A. City RR25843 codes. For additional information including allowable loads loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
|
|
|
|
|
|
|
|
|
|
POST MENDER 4X4IN 13GA STEEL - Case of 4
|
|
|
Reinforcement brackets used to repair rotted or damaged fence posts. Step-by-step instructions labeled onto each. Green corrosion resistant paint finish. 13 Gauge - For 4 x 4 Posts.
|
|
|
|
|
|
|
|
|
|
Tz Post Anchor 6x6in 12ga/14ga - Case of 5
|
|
|
Used to secure wood posts to concrete footings and to provide moisture damage protection. 2-sided with high uplift and bearing capacity. Features a 1" stand-off plate to elevate wood posts above concrete surfaces. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR 25836 codes.
|
|
|
|
|
|
|
|
|
|
Tz Post Anchor 4x4in 18gauge - Case of 25
|
|
|
Secures nominal sized post to wood surfaces offering some lateral and uplift resistance. May be used only for intermediate posts between fully anchored corner/end posts in rail system. Not Recommended for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d HDG fasteners for post and 16d HDG fasteners for base. Meets ICBO 2039 and L.A. City RR23888 codes. For additional information including allowable loads, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
|
|
|
|
|
|
|
|
|
|
Post Base 4x4in Cmpst Elevated - Case of 25
|
|
|
Provides a raised base that elevates wood posts above concrete surfaces to avoid moisture from ground contact. Single-piece design made from composite material; will not corrode. Open center enables installation of metal rod from concrete into post. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning moment loads. Requires (4) 10d HDG nails. ACQ approved.
|
|
|
|
|
|
|
|
|
|
TZ POST BASE 4X4IN ELEV 16GA - Case of 10
|
|
|
Allows installer to pre-align posts and to preset post height above concrete floors or footings. Eliminates post-to-concrete contact for reduced moisture damage. Nails fasten to posts for carports, decks or porches. EPB is welded and primed. EBG is galvanized for added corrosion resistance. Not recommended for fence posts or unrestrained (not fixed or fastened at top) applications.. Requires (8) 16d nails for EPB4408, (12) 16d nails for EPB6608, (8) 16d HDG nails for EBG44-TZ . Meets SBCCI, BOCA - NER 505, ICBO 5736, L.A. City RR 25303 and DSA PA-076 codes. For additional information including allowable loads, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
|
|
|
|
|
|
|
|
|
|
Tz Post Anchor 4x4in16ga/18ga - Case of 10
|
|
|
Used to secure wood posts to concrete footings and to provide moisture damage protection. 2-sided with high uplift and bearing capacity. Features a 1" stand-off plate to elevate wood posts above concrete surfaces. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR 25836 codes.
|
|
|
|
|
|
|
|
|
|
Tz Post Anchor 4x4in 12ga/18ga - Case of 10
|
|
|
Used to secure wood posts to concrete footings and to provide moisture damage protection. 4-sided with high uplift and bearing capacity. Features a 1" stand-off plate to elevate wood posts above concrete surfaces. Drain slots allow the anchors to shed water. Triple zinc finish for ACQ pressure treated lumber. Not for fence posts or unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes.
|
|
|
|
