|
|
|
|
|
|
TAMLYN BT22SP K-Style Gutter Connector, 6-3/8 in L, 7/8 in W, Carbon Steel
|
|
|
TAMLYN K-Style Gutter Connector, Carbon Steel, 6-3/8 in Length, 7/8 in Width
|
|
|
|
|
|
|
|
|
|
TAMLYN BT22ZZSP Storage Strap, 6-3/8 in L, 7/8 in W, Galvanized Steel
|
|
|
Masonry accessory used to tie a brick veneer to the exterior of the house. Two holes provide for nailing on one end, other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8 in x 7/8 in.
|
|
|
|
|
|
|
|
|
|
MiTek JL26IF-TZ Joist Hanger, 4-1/2 in H, 1-1/2 in D, 1-9/16 in W, 2 in x 6 to 8 in, Steel, Zinc, Face Mounting
|
|
|
Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes.
|
|
|
|
|
|
|
|
|
|
MiTek JL28IF-TZ Joist Hanger, 6-1/8 in H, 1-1/2 in D, 1-9/16 in W, 2 in x 8 to 10 in, Steel, Zinc, Face Mounting
|
|
|
Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes.
|
|
|
|
|
|
|
|
|
|
National Hardware N220-350 Mending Brace, 8 in L, 7/8 in W, Steel, Galvanized, Screw Mounting
|
|
|
Designed for reinforcing, attaching, connecting and splicing panels and other home and industrial applications. Product design allows for quick and easy repair of general. household items. Screw holes are countersunk. Boxed loose barcoded.
|
|
|
|
|
|
|
|
|
|
MiTek RT16A-TZ Double Hurricane Tie, 5 in W, 6-1/2 in H, Steel, Zinc
|
|
|
These anchors tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces.
|
|
|
|
|
|
|
|
|
|
MiTek JUS210-2TZ Slant Joist Hanger, 9-1/8 in H, 2 in D, 3-1/8 in W, 2 in L x 10 to 14 in H, Steel, Zinc, Face Mounting
|
|
|
The JUS hanger Series offers double shear nailing. USP's dimple allows for 30 deg to 45 deg nailing through the joist into the header resulting in higher loads and less nailing. Slant/double shear nailing allows for higher load values, fewer nails and faster installation.
|
|
|
|
|
|
|
|
|
|
Squeek No More 1011345 Floor Squeak Repair Screw
|
|
|
Specially scored waxed screws. Scored head breaks off at the same place every time. Carded.
|
|
|
|
|
|
|
|
|
|
Acorn International IHW16100 Insulation Support Wire, 16 in OAL, Carbon Steel
|
|
|
Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2 in less than over center joist spacing. 13 ga.
|
|
|
|
|
|
|
|
|
|
Squeek No More 1010543 Floor Squeak Repair Kit
|
|
|
The Squeek No More kit is designed to stop floor squeaks from above the floor by going safely through the carpet. The kit works on all carpets even berber. The Squeek No More kit has 50 screws that are scored one inch from the head and coated with a special wax that allows the screw to safely pass through the carpet. The tooling, a tripod fixture and driver bit, drives the screw safely through the carpet stopping the score on the screw slightly below the wood of the floor. Then with the tripod fixture you snap the head of the screw off. The screw thread then holds the floor to the joist without having any part of the screw sticking up that you could walk on. The kit also includes 2 joist finding tools. You use these to quickly and accurately find the joist from above the floor.
|
|
|
|
